Rare Parts (automobile & truck): Suspension Parts 1930s to 1995 & Suspension Parts for 1997 (Two Catalogs)

Rare Parts Suspension Parts 1930s to 1995 & Suspension Parts for 1997 (Two Catalogs)

Cars & Trucks
Rare Parts, Inc., Stockton, CAPaperback with holes punched along spine margin
8.3 x 11 inches, 165+ pages

Suspension is the system of tires, tire air, springs, shock absorbers and linkages that connects a vehicle to its wheels and allows relative motion between the two. Suspension systems must support both road holding/handling and ride quality, which are at odds with each other. The tuning of suspensions involves finding the right compromise. It is important for the suspension to keep the road wheel in contact with the road surface as much as possible, because all the road or ground forces acting on the vehicle do so through the contact patches of the tires. The suspension also protects the vehicle itself and any cargo or luggage from damage and wear. The design of front and rear suspension of a car may be different.

An early form of suspension on ox-drawn carts had the platform swing on iron chains attached to the wheeled frame of the carriage. This system remained the basis for most suspension systems until the turn of the 19th century, although the iron chains were replaced with the use of leather straps called thoroughbraces by the 17th century. No modern automobiles have used the thoroughbrace suspension system.

By approximately 1750, leaf springs began appearing on certain types of carriage, such as the Landau.

By the middle of the 19th century,Elliptical springs might additionally start to be used on carriages.

Automobiles were initially developed as self-propelled versions of horse-drawn vehicles. However, horse-drawn vehicles had been designed for relatively slow speeds, and their suspension was not well suited to the higher speeds permitted by the internal combustion engine.

The first workable spring-suspension required advanced metallurgical knowledge and skill, and only became possible with the advent of industrialisation. Obadiah Elliott registered the first patent for a spring-suspension vehicle; each wheel had two durable steel leaf springs on each side and the body of the carriage was fixed directly to the springs which were attached to the axles. Within a decade, most British horse carriages were equipped with springs; wooden springs in the case of light one-horse vehicles to avoid taxation, and steel springs in larger vehicles. These were often made of low-carbon steel and usually took the form of multiple layer leaf springs.

Leaf springs have been around since the early Egyptians. Ancient military engineers used leaf springs in the form of bows to power their siege engines, with little success at first. The use of leaf springs in catapults was later refined and made to work years later. Springs were not only made of metal; a sturdy tree branch could be used as a spring, such as with a bow. Horse-drawn carriages and Ford Model T used this system, and it is still used today in larger vehicles, mainly mounted in the rear suspension.

Leaf springs were the first modern suspension system, and, along with advances in the construction of roads, heralded the single greatest improvement in road transport until the advent of the automobile. The British steel springs were not well-suited for use on America's rough roads of the time, so the Abbot-Downing Company of Concord, New Hampshire re-introduced leather strap suspension, which gave a swinging motion instead of the jolting up-and-down of spring suspension.

In 1901, Mors of Paris first fitted an automobile with shock absorbers. With the advantage of a damped suspension system on his 'Mors Machine', Henri Fournier won the prestigious Paris-to-Berlin race on 20 June 1901. Fournier's superior time was 11 hrs 46 min 10 sec, while the best competitor was Léonce Girardot in a Panhard with a time of 12 hours, 15 minutes, and 40 seconds.

Coil springs first appeared on a production vehicle in 1906 in the Brush Runabout made by the Brush Motor Company. Today, coil springs are used in most cars.

In 1920, Leyland Motors used torsion bars in a suspension system.

In 1922, independent front suspension was pioneered on Lancia Lambda, and became more common in mass market cars from 1932. Today, most cars have independent suspension on all four wheels.

In 2002, a new passive suspension component, the inerter, was invented by Malcolm C. Smith. This has the ability to increase the effective inertia of wheel suspension using a geared flywheel, but without adding significant mass. It was initially employed in Formula One in secrecy, but has since spread to wider motorsport.